Inspect Welding Glove Linings for Wear Before Each Use
Welding gloves can look serviceable while the fabric inside has become thin, scorched or brittle. Heat, sparks and molten metal can reach the hand through worn areas, while damaged seams let grit lodge against the skin. Inspecting the lining before every shift catches failures hidden beneath a sound leather shell.
How to inspect the lining of your welding gloves for wear before each use starts with a few focused minutes, not a quick glance at the leather. Use cool, clean gloves on a dry workbench and bright task lighting, and keep each pair together so wear can be compared. Damaged gloves should leave service; inspection supplements, but never replaces, correct PPE selection and the site’s risk assessment.
Why the Lining Matters More Than the Leather
Welding glove linings commonly use cotton, woven fabric or wool-based felt. Depending on the design, they provide a thermal barrier, absorb sweat and preserve finger movement. They are the final fabric barrier when radiant heat or a spark passes through a hole in the outer leather.
Age, heat and friction can damage fabric faster than the thicker exterior. Look for pinholes, thin spots, broken fibres and loose stitching. A seam opened at the cuff can expose the wrist even when the palm appears intact.
Australian jobsites add abrasive conditions. Structural steel work around Newcastle can expose gloves to sharp edges and grinding dust, while Pilbara mining crews may handle gritty ore dust. Embedded abrasive particles work into the lining and gradually cut its fibres.
Prepare the Gloves for Inspection
Allow used gloves to cool before handling them. Check them in a clean, well-lit area away from hot metal, active welding and solvent fumes. Wash and dry your hands first, and do not inspect a glove while its lining is wet from cleaning.
Open the cuffs fully and examine each glove in the same sequence: cuff join, palm, fingers, thumb gusset, then beneath seams and reinforcement patches. Look only as far as the construction allows; do not pull out an attached liner or prise apart stitching. Check the maker’s label and care instructions as well.
Identify Heat, Abrasion and Contamination Damage
Small holes and thin patches are easiest to miss near finger creases and the thumb. Compare the glove with its pair under good lighting. Frayed threads, bald areas, gaps between layers or exposed filling mean it should not be used.
Heat damage can appear as scorch marks, a melted sheen, bubbling, hardening or an unusually smooth, glazed surface. The fabric may feel brittle. Sudden discolouration after welding, a burn or a flash-fire event warrants replacement even if the leather still looks sound.
Oil, fuel, solvent and chemical residues can weaken fibres or create a fire risk, while damp fabric may transmit heat more readily than dry fabric. A lining that smells sour, feels clammy or contains dirt needs attention. Clean only by the approved method and replace it if contamination cannot be removed safely.
Check Fit, Movement and Electrical Suitability
Flex each finger and press the palm lightly to feel for weak spots and restricted movement. The glove should fasten fully, with no pinching at the thumb or cuff. A stiff lining, bunching fabric or reduced dexterity can indicate internal damage or poor fit.
Check glove length against the task. A short cuff may leave a gap between the glove and leather sleeve or flame-resistant (FR) shirt, while an oversized glove can catch on hot metal. Any protection rating must match the welding process, materials, heat exposure and site requirements.
Leather welding gloves are not automatically electrical-insulating or arc-rated PPE. For work around 230-volt electrical equipment, licenced electricians still need the controls and PPE required by the electrical safety procedure. Heat clothing may be specified under AS/NZS 2161.4 and arc-rated clothing under AS/NZS 2975, so verify the product-specific rating rather than trusting an FR label.
Care and Storage Protect the Hidden Layer
Follow the supplier’s cleaning instructions; many welding gloves must not be machine-washed, solvent-cleaned or tumble-dried. Let them air-dry away from sparks and direct heat. A dryer, workshop heater or sunlight can shrink or embrittle fibres. If a glove has a removable liner, follow the manufacturer’s removal and cleaning instructions.
Store clean, dry gloves loosely in a ventilated pouch or drawer, away from oils, acids and welding spatter. Do not seal damp gloves in plastic or leave them on a hot vehicle dashboard. The intense summer sun in Perth and humid conditions in Townsville make correct storage especially important.
Replace gloves after heat damage, persistent contamination or a significant loss of strength and dexterity. Condition, task and manufacturer guidance matter more than a fixed expiry date. For restocking, UR Shield’s direct-to-customer model offers affordable pricing, free shipping, bulk orders and easy returns for Australian crews in regional and metro areas.
Make the Check Part of Every Shift
Safe Work Australia guidance calls for PPE suitable for the identified hazards. Recording inspection outcomes and separating rejected gloves from usable stock helps maintain that control, especially when several people share a workshop or site store.
Pre-use lining inspection checklist
- Unroll each glove and check the cuff, palm, fingers and thumb under bright lighting, comparing it with its pair.
- Look for holes, worn patches, thinning, frayed fibres, scorch marks, loose stitching and separated layers.
- Press and flex the lining gently, rejecting fabric that feels brittle, glazed, sticky or unusually thin.
- Check for damp, sweat, oil, chemical residue and embedded grit, using only the approved cleaning method.
- Confirm that the glove still fits, fastens fully and allows controlled finger movement.
- Tag failed pairs for removal from service and record the reason before arranging a replacement.
| Check | Normal appearance | Warning sign | Required response |
|---|---|---|---|
| Surface | Consistent texture and colour | Thin, rough, scorched or glazed | Replace if changed from its expected condition |
| Openings | No holes or worn spots | Pinholes, splits or exposed filling | Remove from service |
| Seams | Secure, even stitching | Loose stitching, gaps or separated layers | Remove from service |
| Heat damage | No melting or hardening | Burnt, bubbled, fused or brittle areas | Remove immediately |
| Moisture and dirt | Clean and dry | Damp, stained, oily or gritty | Clean as instructed; replace if not restored |
A visual check cannot prove remaining heat resistance or compliance with a rated standard. Manufacturer guidance, recorded exposure and incident history still govern replacement decisions.
Before the next hot-work task, record the inspection result for every glove pair in the site’s PPE log.